smartphonefirmwares

Q Mobile I2 Pro Sc7731 Firmware

—

by

admin
in
Q MOBILE I2 PRO SC7731 FIRMWARE FLASH FILE

Q Mobile I2 Pro Sc7731 Firmware Flash File

Q Mobile I2 Pro Sc7731 Firmware Flash File

Q Mobile I2 Pro Sc7731 Firmware Flash File
==== Wait for phone…
Phone found! [ 233 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Prepare Ok!
– > Wait phone connected …
Phone found! [ 233 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
– > Wait phone connected …
Phone found! [ 233 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : i2_PRO
Model Brand : QMobile
Model Device: i2_PRO
AndrVersion : 5.1
BaseBand CPU: I2 PRO
Project Ver : QMobile_i2_PRO_MP_09_11
Model Ext : QMobile i2 PRO
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now …
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.43.3_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img
Elapsed: 00:07:31
Reconnect Power/Cable!

Early steps to Install Stock ROM on Q Mobile I2 Pro 


  1. Download and Install Spreadtrum USB Driver on your Computer
  2. Download and  Spreadtrum Upgrade Tool on your compute

How To Flash Q Mobile I2 Pro 

  1. Download and Install Spreadtrum USB Driver on your Computer. If in case Spreadtrum Driver is already installed on your computer then SKIP this Step.
  2. Download .pac firmwarefor your device (Itel, other)
  3. Download and extract Spreadtrum Upgrade Tool on your computer.
  4. Now, open UpgradeDownload.exe.Once Spreadtrum Upgrade Tool is launched, connect your Android device to the computer (make sure your device is switch off).
  5. If Smartphone is properly connected to the computer, click on the Load Packed Button and add the .pac file (stock rom which comes as .pac).
  6. Having successfully added the .Pac file in Spreadtrum Upgrade Tool, click on the Start Downloading button to begin the flashing.
  7. During the flashing process your device will restart automatically.
  8. Once flashing is completed, you will be able to see the Green Passed Message in Spreadtrum Upgrade Tool.
  9. Now you have successfully flashed your Android Device using Spreadtrum Upgrade Tool.
  10. Note after flashing phone on must 5 to 10mins
  11. During the flashing process your device will restart automatically. Once flashing is completed, you will be able to see the Green Passed Message in SPD Upgrade Tool
  12. After flashing process starts and might take up to 5-10 minutes. So keep patience and wait
  13. See detailed Instruction Spreadtrum Upgrade Tool with images

  14. password:mobilesfirmware/i2pro



Comments

Leave a Reply

Your email address will not be published. Required fields are marked *